When ordering replacment parts for your ClubRunner, specify the part numbers
as shown on the following list. To help identify the part number, download and
print (if necessary) this two-page
Parts
Diagram (a 74Kb Adobe .pdf document) Requires the
free Acrobat
Reader software). Minnimum replacement part charge is $3 (shipping and
handling additional).
Mechanical Components |
| ||||
| 1. Chassis | | 2. Motor Includes the K2300 gear installed on the motor shaft. | | 3. Roll Pin |
| ||||
| ||||
| 4. Pulley | | 5. Screw - No. 10-32 x 3/4 Three Required. | | 6. Shaft |
| ||||
| ||||
| 7. Rear Axle Bearings Two Required. | | 8. Pully Gear Has the two K0040 bearings pressed into the gear. | | 9. Bearing Two required. |
| ||||
| ||||
| 10. Thrust Washer | | 11. Drive Belt | | 12. Rear Axle |
| ||||
| ||||
| 13. Mounting Bearing | | 14..Screw 1/4-20 x 1/2 Two required | | 15. Hex Nut Two required |
| ||||
| ||||
| 16. Output Gear | | 17. Pin-Drive Shaft | | 18. Thrust Washer |
| ||||
| ||||
| 19. Cover-Gearcase | | 20. Screw-No. 8-16 x3 /4 Six required. | | 21. Plate-Control Board Mounting |
| ||||
| ||||
| 24. Control Board Assembly | | 24A. Shrink Tube Two required. | | 25. Screw-No 8-32 x 1/2 |
| ||||
| ||||
| 26. Hex. Nut | | 27. Screw-No. 8-32 x 3/8 Two required. | | 29. Leadwire-Control Board |
| ||||
| ||||
| 30. K0602 - Leadwire-Battery For older, 1K style carts. | | 30. K0604 Leadwire-Battery New style, 10 K ohm ( photos available here). | | 31. Release Knob |
| ||||
| ||||
| 32. Release Knob Spring | | 33. E-Ring | | 34. Tension Knob |
| ||||
| ||||
| 35. Hex Nut | | 36. Clutch Assembly-Left Hand | | 37. Clutch Assembly-Right Hand |
| ||||
| ||||
| 38. Drive Pin Two required. | | 39. Rear Wheel with bearings Two K0010 bearings are pressed in. If you need a new hub cap it must be ordered separately. | | 40. Bearing Four required. |
| ||||
| ||||
| 41. Washer - Rear Axle Two required. | | 42. Retaining Ring - Wheel Two required. Need retaining ring pliers? Order here. | | 43. Hub Cap - Rear Wheel Two required. |
| ||||
| ||||
| 44. Front Wheel Tube Now made of steel. You must replace the K0110 if the cart is older than March of 1996. | | 45. Front Wheel Housing We also recommend that you replace the screws (k2101 - 2 required) because once you remove the old screws, you break the loctite bond and the old screws will not hold. | | 46. Screw-#10-24 x 1 3/4 |
| ||||
| ||||
| 46A. Screw-#10-24 x 1 1/2 | | 47. Hex Nut Two required. | | 48. Front Wheel |
| ||||
| ||||
| 49. Nyliner Bearing - Front Wheel | | 50. Front Axle | | 51. Screw-1/4-20 x 1/2 Two required |
| ||||
| ||||
| 52. Handle Tube All handle tubes are the newer S-shaped tube where the cord runs in a channel in the back of the tube. If you have the older style single bend tube you will also have to replace your cord (K0700) and this requires some soldering. | | 53. Cord Handle | | 55./56. Right and Left Handle |
| ||||
| ||||
| 58. Screw - No. 8-18 x 5/8 Seven required. | | 59. Speed Selector Knob | | 60. Upper Bag Rest |
| ||||
| ||||
| 61. Screw-1/4-20 x 1 3/4 | | 62. Hex. Nut-Bag Rest | | 63. Velcro Strap Set Each set consists of one short and one long strap and can be used on either the upper or lower bag rest. Each cart therefore has two sets of straps. |
| ||||
| ||||
| 66. Battery Cover | | 68. Battery-31amp Battery lead wire, which plugs the battery into the cart (K0602 or K0604), can either be taken off your old battery or can be ordered separately. $105 including shipping | | K8635 - Front Wheel Assembly including Steel Tube Does not include velcro strap (K3801). |
| ||||
| ||||
| K8636 - Front wheel assembly without Steel Tube Does not include velcro strap (K3801). | | Accumate Pro 12 volt 7 amp charger Multi stage charger with 7 amp constant current for fast and thorough charging. Also has temperature regulated monitoring. | ||
|